The Kodiak Disc Brake Kit # K2HR79E is not able to be separated, but I do have another option available.
The Dexter Disc Brake Kit - 12-1/4" Hub/Rotor - Grease - 8 on 6-1/2 - E-Coat - 8,000 lbs # K71-635-90 will use the same bearings and will be able to be separated, making replacements easier if needed. The E-coat finish provides corrosion resistance for freshwater and limited saltwater use as well. With this also being made in the U.S.A., it will be a great option. view full answer...
If you are looking to purchase the current model of the Thule EasyFold XT Bike Rack for 2 Electric Bikes - 1-1/4 and 2 Hitches - Frame Mount, the correct model number for that particular rack is # TH903202.
If you provide the year/make/model of vehicle you have as well as the hitch size (if you have one), I would be happy to confirm with you if the EasyFold XT will fit your vehicle. view full answer...
The shipping weight of the Fastway # FA92-00-0600 e2 system is right at 90 lbs, with the Husky # HT32215 system weighing in at around 105 lbs, a pretty minimal difference.
Either would be a good choice, but I'd give the Husky system an edge becasue its sway control component is a bit more effective. The Husky system use a 4 point sway control system, with friction resistance provided in the head where the trunnion bars attach and at the contact point between the frame brackets and the... view full answer...
The # BDW20284 is what's known as a 'momentary' type switch. It will stay on as long as it remains pushed. Once you release the switch, it'll turn off.
If you were needing a standard on/off type rocker switch that remains on until turned off, use # BDW20285. The switch has a 20A capacity. view full answer...
I'm sorry to hear about what happened to your Camco RV Wash Brush. Unfortunately, the brush portion by itself is not available as a separate item, which means you will need to replace the entire Camco Adjustable Flow Through RV Wash Brush # CAM41960.
The Camco brush is adjustable from 47" to 74" but if you don't need quite as much length, another option to consider is the SM Arnold Bi-Level Vehicle Cleaning Brush with Telescoping Flow-Thru Handle - 10" Cleaning Head # 38125-670.
The SM... view full answer...
The highest rated 8 inch wheel/tire combo we offer would have an 'M' speed rating, which is good up to 81mph. This would be a 215/60-8 bias ply tire mounted on a 8 x 7 inch wheel with a 4 on 4 bolt pattern. The tire has a C load rating, with a weight capacity of 940 lb per tire/1880 lb per axle. The wheel/tire combo is available with a white powder coated wheel as part # AM3H290 or a galvanized wheel as part # AM3H300. This is as close to 100mph that anything we offer would get. view full answer...
Ok, so for electric trailer brakes, the color of the wires coming out of the brakes does not actually matter for the electric brakes we offer.
For example, Dexter Electric Trailer Brake Kit - 10" - Left and Right Hand Assemblies - 3,500 lbs # 23-26-27 uses two green wires, and either can be connected to your ground and brake wiring, as you can see at about the 6:35 mark of the linked installation video of these brakes.
As another example, the Electric Trailer Brake Kit - Self-Adjusting... view full answer...
There is not an option for a plug-in brake controller in the traditional sense for your 2009 Tiffin Allegro motorhome, so you would need to hardwire in a brake controller like the Tekonsha Prodigy P3 Trailer Brake Controller # 90195.
The only exception to that would be Curt Echo Wireless Trailer Brake Controller # C51180.
Since you mentioned you already had a working 7-way, you would be able to plug the Echo right into the 7-way with absolutely no additional wiring necessary. I have added... view full answer...
You have 2 choices at this point.
For the first option, you could use an extender like # HES6 which would provide an additional 5-3/4 inches of clearance for your Thule T2 Pro XTR, part # TH69TX which would allow it to fold but using an extender would reduce the tongue weight capacity (maximum amount of downward force that can safely be applied to the receiver) by 50%. This won't be a problem, as the # 75237 hitch you purchased has a very substantial 675 lb tongue weight capacity. Half... view full answer...
The circuit you're looking to access is known as the CHMSL (center high mounted stop lamp). I've looked through the forums, and saw several folks mention that there should be a white wire with a purple stripe buried in the harness than runs along the passenger side frame rail. Barring that, the easiest place to access that circuit would be at the 3rd stop lamp atop the back of the cab.
The # 118384 would access the brake lamp circuit for you, but the turn signal is also carried on that... view full answer...
Your 2018 Ford F-150 has an electric speedometer and should not record mileage if the ignition is off.
That said if they used a braking system like the Brake Buddy Select 3 # HM39524 that requires power to the 12 volt outlet and they did not install a separate outlet for it then at that point they would have been leaving the ignition on to power the brake controller. view full answer...
You can absolutely remove your Rota-Flex pin box and replace it with a Reese Sidewinder without any issue. It will work superbly on your standard bed F-350 and allow you to go from a sliding hitch to a fixed hitch.
The pros are the convenience the Sidewinder offers, being able to go to that lighter fixed hitch and not having to use the slider function of a hitch. The only con is the Sidewinder doesn't have the rubber compound in the front of the pin box to absorb as much road shock as... view full answer...
The Jif Marine Folding Pontoon Ladder part # JIF38FR is indeed constructed of stainless steel. It has a shipping weight of 8 lbs so the actual weight will be a few less, likely 6-7 lbs. view full answer...
In order to properly measure your RV's vents, you will want to measure the size of the rough opening in your RV's roof. This can be measured by removing the garnish around the vent on the inside of the RV and measuring the size of the rough opening.
The most common RV vent's measurements are 14" x 14" like the MaxxFan Deluxe Roof Vent w/ 12V Fan and Thermostat # MA00-06200K. view full answer...
The Edge Monitor # EP84130 is a display-only device. This product does not alter your engine tune or performance in any way. Rather it provides a monitoring function for up to 8 available engine parameters. These vehicle parameters will vary based on the year/make/model/version of the vehicle. It connects to the vehicle computer via the OBD-II port.
Monitor products do offer a driving coach function which analyzes your driving habits to help you improve your fuel economy. Any improvements... view full answer...
The Replacement Slider Base for B&W Companion Slider 5th Wheel Trailer Hitch - 20,000 lbs # BWRVB3405 is the sliding base for the 5th wheel head # BWRVC3006. The used product RU-16-B5-00310756 you mentioned is a fully functioning sliding base that was used for a test fit and got some surface scratches. It will perform as new. You can click on the used product and see the photos we have of the scratches and dents to see if you are still interested.
Let me know if you have other questions. view full answer...
According to the (15 U.S.C. ยง 230) Magnuson-Moss Waranty Act, no one thing would void the entire warranty on a vehicle. If it were proven that this one item cause a specific damage then they could deny a claim related to that one part. TorkLift products are proven effective and safe and do not have a history of issues. I would buy TorkLift products with confidence.
Both TorkLift # TLA7310 and # TLA7311 are a confirmed fit for your F250. The 7310 is for leaf springs that are already... view full answer...
I reached out to the manufacturer and was able to confirm that the STKR Concepts FLi PRO Telescoping Light # RR24XP can be charged with a USB to USB Type-C charger so you would be able to connect it to your powerbank to recharge it. They also stated that it can be used while charging so you could essentially turn it into a standard plug in light if you didn't want to use the battery. view full answer...
Thank you very much for your purchase directly from etrailer; the 3/4" gap with the # HAP-105-205-03 is fine as they need an appropriate amount of movement. If there wasn't that gap the suspension would be quite stiff and wear out quickly due to consistent contact. view full answer...
Go To Results